Jeep key fob battery replacement in five minutes
A Jeep key fob battery replacement fixes most 'dead fob' problems for a few dollars. This guide shows which coin cell your Jeep takes, how to open the fob without damaging it, and what to do if it still won't work.
It covers Grand Cherokee, Wrangler, Gladiator, Cherokee, Compass and Renegade fobs. No reprogramming is needed.
- Which battery your fob takes
- How to open the fob
- What to check if it still won't work
- How to start with a dead fob
Key takeaways
- CR2032 is the usual cell Owner’s manuals for many Jeep models specify one CR2032 coin cell.
- Check newer fobs Some newer Jeeps, notably the Wrangler JL and Gladiator, are widely listed with a CR2450 instead.
- Quality matters Mopar warns that some aftermarket coin cells don’t match the original dimensions. Use a quality branded cell.
- No reprogramming needed The fob keeps its pairing when the battery is changed.
Which battery does my Jeep key fob take?
Mopar owner's manuals for many recent models say the replacement battery is one CR2032. They also advise using a Mopar battery, because aftermarket coin cells may not match the original dimensions. In practice a quality branded cell from Energizer, Duracell or Panasonic is the sensible alternative; cheap no-name cells are the ones most likely to sit loosely.
Some newer Jeeps, notably the Wrangler JL and Gladiator, are widely listed with a CR2450 instead. Whatever you drive, read the code on the old cell before you buy.
Jeep key fob battery by model

How to replace a Jeep key fob battery
-
Remove the emergency key
Slide the release latch on the back of the fob and pull out the metal emergency key.
-
Find the opening
Look in the slot the key came from, or along the seam, for the point where the case separates.
-
Separate the halves gently
Use a small flat plastic tool or the emergency key, working along the seam with light sideways pressure. Don’t force one spot.
-
Swap the cell
Note which way up the old cell sits, then push the new one under the small lip with your thumb so it seats fully.
-
Close and test
Snap the case together, reinsert the emergency key until it locks, then test the buttons and push-button start.
Best batteries for your Jeep fob
The safe default for most key fobs
Energizer’s CR2032 is the cell to reach for when your fob takes a 2032. Fobs draw short bursts of power with every button press and every keyless check, and branded lithium cells handle that well. The cells are uncoated, so they make clean contact in tight holders. A four-pack covers your main fob, your spare and the next swap.
- Fits the most common fob size
- Uncoated for clean contact
- Four-pack covers both fobs
- Buy from Amazon itself or a known retailer: fakes exist
- Packaging is fiddly
An uncoated cell from a major coin-cell maker
Panasonic publishes full specifications for its CR2032 and the cells have no bitter coating, so they make clean contact in tight fob holders.
- Uncoated, clean contact
- Published specs
- Child-resistant pack
- Not always in stores when you need one today
A trusted brand with a child-safety coating
Duracell’s key fob cells carry a bitter coating that discourages children from swallowing them. The trade-off is that the coating occasionally stops a cell making good contact in tight holders; if a new one doesn’t work, wipe it with an alcohol wipe or try an uncoated cell.
- Bitter coating for child safety
- Packaged for key fobs
- Easy to find
- Coating can cause poor contact in some fobs

Still not working after a new battery?
- Check the orientation and that the cell is pushed fully under its lip.
- Try a different branded cell. Undersized aftermarket cells can sit loosely.
- Check the contacts. Some owners have restored a fob by very gently raising the contact prongs under the battery.
- Try the spare fob. If it works, the first fob may be damaged.
- If both fail, see our guide to Jeep key fob problems.
More help: why a key fob stops working after a battery change and best car key fob batteries.
If the push-button ignition won’t respond, the fob battery may be low. Stellantis owner’s manuals describe a backup method: hold the nose of the fob (the end opposite the emergency key) against the START/STOP button and press it with your foot on the brake. Use the hidden emergency key to open the driver’s door.
Mopar’s owner information explains the backup starting method and the key fob battery replacement for its vehicles.
Jeep key fob battery FAQ
What battery does a Jeep key fob take?
Most take one 3V CR2032. Some newer fobs are sold with a CR2450, so check the code on your old cell.
Do I need to reprogram the fob after changing the battery?
No. It keeps its programming.
Why does Mopar say to use a Mopar battery?
Its manuals note that some aftermarket coin cells don’t match the original dimensions. A quality branded cell avoids most problems.
How do I start with a dead fob?
Hold the nose of the fob against the START/STOP button and press it with your foot on the brake.
How long does the battery last?
Typically a few years. Keyless entry and remote start use more power, so heavy users may need one sooner.
The bottom line
- Most fobs take a CR2032
- Use a quality branded cell
- No reprogramming needed
- Nose-of-fob backup start
A Jeep key fob battery replacement takes five minutes: remove the emergency key, open the case gently, fit a quality CR2032 (or the size printed on your old cell) the same way up, and test. If the push button won’t respond, hold the fob’s nose against it.



