Programming a GMC key fob: what you can do yourself
Programming a GMC key fob is something many US owners can do at home. GM's owner's manuals include a do-it-yourself procedure for push-button-start vehicles, and a 30-minute routine for adding a fob when you don't have two working ones. Here's how it works, and when to call a locksmith instead.
It applies to push-button-start GMC models such as the Sierra, Yukon, Acadia and Terrain. Turn-key models use a similar idea, but the steps differ, so check your manual.
- The two GM programming procedures
- What you need before you start
- When a locksmith or dealer is better
- Choosing a replacement fob
Key takeaways
- Two working fobs? It's quick With two recognized fobs you can add another in a few minutes using the driver’s door lock and the Start button.
- No working fobs? Allow 30 minutes US owners can run a roughly 30-minute relearn. It erases every old fob, so have them all with you.
- A new fob needs a cut blade The emergency key inside the fob must be cut to match your locks.
- Canada is different Canadian vehicles need a dealer when two recognized fobs aren’t available.
How GMC key fob programming works
A GM fob does two jobs: it locks and unlocks the doors by radio, and it tells the immobilizer the vehicle is allowed to start. On push-button-start models, programming a new fob teaches the vehicle both at once.
GM's owner's manuals describe two procedures. One is for when you already have two recognized fobs. The other is a longer relearn for when you don't, which US owners are allowed to use but Canadian owners aren't. Both use the driver's door lock cylinder, so you'll need the metal key cut to fit.
Terms you'll see
- Transmitter
GM’s word for the key fob.
- Recognized transmitter
A fob that’s already programmed to this vehicle.
- DIC
The driver information center, the screen in the instrument cluster that guides you through programming.
- Transmitter pocket
The backup spot where the vehicle reads a fob at close range; programming often uses it or the cupholder.
Programming with two recognized fobs
-
Get set up
Turn the vehicle off and bring every fob with you. Remove the cap from the driver’s door handle lock cylinder and put the two recognized fobs in the cupholder.
-
Enter programming mode
Insert the key into the driver’s door lock and turn it to unlock five times within 10 seconds. The DIC should say it’s ready for the next remote.
-
Learn the new fob
Place the new fob in the cupholder or transmitter pocket and press ENGINE START/STOP. Wait for the DIC to confirm.
-
Confirm and finish
Remove the fob and press Lock or Unlock. To add more, repeat. When done, press and hold ENGINE START/STOP for about 12 seconds.
Exact wording and fob placement vary by model and year. Follow your owner’s manual section ‘Programming Transmitters to the Vehicle’.
Programming without two recognized fobs (about 30 minutes)
-
Start the relearn
With the vehicle off, turn the key in the driver’s door lock to unlock five times within 10 seconds. The DIC shows a ‘remote learn pending’ message.
-
Wait and press Start, three times
After about 10 minutes the DIC asks you to press the Start button. Press it, then repeat twice more. After the third time, all old fobs stop working.
-
Learn each fob
Place a fob in the cupholder, press ENGINE START/STOP, wait for the DIC, then remove it and press Lock or Unlock. Repeat for every fob you want to keep.
-
Exit
Press and hold ENGINE START/STOP for about 12 seconds.
This erases every fob that isn’t relearned, so have all your fobs with you. Not available on Canadian vehicles.
GM’s technician guidance stresses keeping fobs that aren’t being programmed away from the vehicle during key learning, at least about 10 feet in the dealer procedure. A stray fob nearby is a common reason programming fails.

When to use a locksmith or dealer instead
DIY programming isn't always possible. Turn-key models use a different procedure, some models need a scan tool, and owners often report that aftermarket fobs don't always program with the onboard routine. A mobile auto locksmith can cut the blade and program the fob with professional equipment in one visit, usually for less than a dealer. See GMC replacement key cost for typical prices.
Also read how to program a key fob yourself and how to get a spare car key for the general picture.
Replacement fobs for your GMC
GMC replacement fobs compared
For the latest push-button-start GM pickups
Listed for 2022–2025 Sierra and Silverado trucks with push-button start, which use a newer smart key than the 2019–2021 trucks. A good-value way to add a spare. Check that the FCC ID and part number printed on your current fob match the listing before you buy.
- Covers the current GM trucks
- Cheaper than a dealer fob
- Proximity entry and start
- Programming usually needs a locksmith or dealer
- Aftermarket feel
A well-reviewed spare for current GM SUVs
SUPALAND’s smart key is listed for 2021-and-later Yukon, Tahoe and Suburban models. SUPALAND fobs are a popular aftermarket choice and are shipped tested. Check that the FCC ID and part number printed on your current fob match the listing before you buy.
- Covers 2021+ Yukon, Tahoe, Suburban
- Pre-tested by the seller
- Low price for a smart key
- Professional programming usually needed
- Not genuine GM
For turn-key GM models with the flip-out blade
The OHT01060512 flip key was used on a long list of turn-key GM models, including many Equinox, Terrain, Sonic and Cruze years. Keyless2Go’s replacement includes the remote and a blank blade to be cut. Check that the FCC ID and part number printed on your current fob match the listing before you buy.
- Wide GM fitment
- Low cost
- Remote and blade in one
- Blade must be cut and the chip programmed
- Not for push-button-start cars

If you only have one working fob, add a second now. With fewer than two recognized fobs, the quick procedure isn’t available and you’d need the 30-minute relearn, which erases any fob you don’t have with you, or a locksmith. See what to do if you lose your only car key.
Programming a GMC key fob FAQ
Can I program a GMC key fob myself?
On many push-button-start models, yes. With two recognized fobs it takes a few minutes; without them, US owners can run a roughly 30-minute relearn.
Do I need the blade cut?
Yes. The emergency key inside the fob is used in the door lock during programming and to get in if the fob dies.
Will programming erase my old fobs?
Adding a fob with two recognized fobs keeps them. The 30-minute relearn erases every fob you don’t relearn.
How many fobs can I program?
It depends on the model; GM manuals typically allow up to eight remotes. Check your manual.
Why won't my new fob program?
Check the FCC ID matches, the fob battery is fresh, and other fobs are well away from the vehicle. Some aftermarket fobs need a locksmith’s tool.
The bottom line
- Two fobs: a few minutes
- No fobs: about 30 minutes
- Cut the blade first
- Locksmith if DIY fails
Programming a GMC key fob is often a DIY job: a few minutes with two working fobs, about 30 minutes without. Get the blade cut first, keep other fobs away, and use a locksmith if the onboard routine won’t take the new fob.






