The best car amplifiers and subwoofers
Car amplifiers and subwoofers are what turn a decent car stereo into a system with real weight and headroom. An amplifier gives your speakers clean power so music stays clear at highway volume, and a subwoofer takes over the deepest notes your door speakers can't play. We picked four amplifiers and four subwoofers from Rockford Fosgate, Kicker, Alpine and Pioneer, from a plug-in power pack for factory stereos to a ready-built dual 10-inch enclosure, and explain how to match them.
- Rockford Fosgate's R2-300X4 is the best 4-channel amp for most speaker upgrades
- Rockford Fosgate's Punch P300-12T is the easiest way to add a 12-inch sub
- Kicker's dual CompR 10 enclosure with the CXA800.1 amp is our pick for big bass
Key takeaways
- Two kinds of amp A 4-channel amp powers your door speakers. A mono amp powers a subwoofer.
- Match RMS, not peak Choose an amp whose RMS output at your sub’s impedance is close to the sub’s RMS rating.
- Powered subs are easiest An amplified sub has the amp built in: one box, one wiring kit.
- Budget for wiring Every amp needs a properly sized power cable, fuse and ground.

Car amplifiers compared
|
Best 4-channel
Rockford R2-300X4
|
Best mono
Rockford R2-500X1
|
Dual subs
Kicker CXA800.1
|
Factory stereos
Alpine KTP-445U
|
|
|---|---|---|---|---|
|
|
|
|
|
| Channels | 4 | 1 (mono) | 1 (mono) | 4 |
| RMS power | 50 W x 4 at 4 ohms | 500 W at 2 ohms | 800 W rated | 45 W x 4 at 4 ohms |
| Use it for | Door speakers | One subwoofer | Two subs | Speakers, factory radio |
| Our score | 9.1 /10 | 8.9 /10 | 8.8 /10 | 8.6 /10 |
| Price | – | – | – | – |
| View | View | View | View |
Car subwoofers compared
|
Best powered
Rockford P300-12T
|
Big bass
Kicker Dual CompR 10
|
Best shallow
Rockford P3S 10
|
Budget
Pioneer TS-A2500LS4
|
|
|---|---|---|---|---|
|
|
|
|
|
| Type | Powered, in box | 2 subs in box | Driver only | Driver only |
| Power | 300 W amp built in | Needs ~800 W amp | 300 W RMS | 300 W nominal |
| You also need | Wiring kit | Mono amp, wiring | Box, amp, wiring | Box, amp, wiring |
| Our score | 9.0 /10 | 8.9 /10 | 8.7 /10 | 8.3 /10 |
| Price | – | – | – | – |
| View | View | View | View |
How we chose the best car amplifiers and subwoofers
We did not bench-test this gear. We compared the makers’ published RMS ratings, features and dimensions with dealer data and owner feedback, and picked established brands sold on Amazon.com.
-
Honest power ratings
We compared RMS (continuous) power, not peak, and favored brands with a record of accurate ratings.
-
Easy matching
We chose amps and subs that pair naturally, so you can build a system without guesswork.
-
Fit
We included compact amps, a slim truck enclosure and shallow subwoofers for cars with little space.
-
Tuning features
Adjustable crossovers, bass boost, subsonic filters and remote level controls make a system easier to set up well.
The best car amplifiers and subwoofers: detailed reviews
Amps and subs work best with a head unit that has clean pre-outs and good sound controls; see our best car stereos guide. For how they fit into a whole system, read our car audio guide.
Best car amplifiers
The best amp for a speaker upgrade
A 4-channel amp is the upgrade that lets new door speakers sound their best at speed. Rockford Fosgate’s R2-300X4 delivers 50 watts RMS x 4 at 4 ohms, 75 watts x 4 at 2 ohms, or 150 watts x 2 bridged, from a compact 1.9 x 6.8 x 10.1-inch Class D chassis that runs cool and places little demand on the car’s electrical system.
Fully adjustable 12 dB/octave high- and low-pass crossovers let you keep deep bass out of the doors, and Rockford’s C.L.E.A.N. circuitry helps you set the gains correctly. It is a great match for the speakers in our best car speakers guide.
- 50 W x 4 RMS at 4 ohms
- Compact, efficient Class D design
- Adjustable crossovers
- Gain-setting help built in
- Not enough for a large subwoofer on its own
A compact amp for one subwoofer
A mono amplifier is designed for subwoofers. The R2-500X1 produces 300 watts RMS at 4 ohms or 500 watts at 2 ohms from a chassis just 1.9 x 6.8 x 8.5 inches, small enough to hide under a seat or behind trim. Its Class D design is efficient, so it doesn’t strain the car’s charging system.
A variable infrasonic filter protects the sub from wasted low-frequency energy, Punch EQ adds bass where small cabins need it, and a remote level control lets you adjust bass from the driver’s seat. It pairs well with a single 10- or 12-inch sub such as the Rockford Punch P3S 10.
- Up to 500 W RMS at 2 ohms
- Small footprint
- Remote bass level control
- Single-sub systems only
Power and flexibility for bigger bass
Kicker’s CXA800.1 is the amp we’d pair with the Kicker dual CompR 10 enclosure. It is an 800-watt Class D mono amp that is stable down to 1 ohm, giving you freedom in how you wire multiple subwoofers.
Tuning tools include a variable 12 dB crossover, KickEQ bass boost of up to 6 dB, and a 24 dB subsonic filter. It works with as little as 9 volts from the battery and accepts speaker-level signals of up to 40 volts, so it can connect to a factory stereo as well as an aftermarket one. Mounting hardware for vertical or horizontal installation is included.
- 800 W mono output
- Stable down to 1 ohm
- Works with factory or aftermarket stereos
- Subsonic filter and bass boost
- Needs heavy-gauge wiring
- Larger than the Rockford
More power without a big install
Alpine’s KTP-445U is a compact 4-channel amp designed to sit behind the stereo or under the dash. It delivers 45 watts RMS x 4 at 4 ohms, roughly double or triple what most head units produce, and is rated to the CEA-2006 standard so the figure is honest.
Alpine designed this universal version to work with all aftermarket and factory receivers, with an adjustable gain switch. It is ideal if you want more clarity and volume from new speakers without running a separate amp to the trunk.
- Fits behind the dash
- 45 W x 4 RMS, CEA-2006 rated
- Works with factory and aftermarket stereos
- No crossovers for subwoofer use
- Less power than trunk-mounted amps

Best car subwoofers
A complete bass system in one slim box
If you want proper 12-inch bass without matching separate parts, the P300-12T is the easy answer. Rockford Fosgate puts a 12-inch subwoofer and a 300-watt Class D amplifier in a slim sealed enclosure (15 x 25.8 inches, tapering from 8.5 to 4.8 inches deep) designed to fit behind the seat of many trucks or flat in a trunk.
It has speaker-level inputs for factory stereos and line-level inputs for aftermarket ones, plus an adjustable 12 dB/octave low-pass crossover, bass boost and a phase switch. All you need is a wiring kit.
- 12-inch sub with matched 300 W amp
- Slim enclosure fits behind truck seats
- Works with factory or aftermarket stereos
- Less output than a big separate system
Big, punchy bass ready to install
Kicker’s 48DCWR102 is two CompR 10-inch subwoofers in a factory-tuned vented enclosure with thick MDF walls and internal bracing. Because the box is already designed for the drivers, you skip the hardest part of building a sub system.
It presents a 2-ohm load and is designed for about 800 watts RMS, which makes the Kicker CXA800.1 a natural partner. Vented boxes play louder and deeper than sealed boxes, so this suits rock, hip-hop and electronic music, but it does take up a good part of the trunk.
- Two 10-inch subs in a tuned box
- Vented design for deep, loud bass
- Strong, braced MDF construction
- Takes significant trunk space
- Needs a powerful mono amp
Real bass where space is tight
Shallow-mount subwoofers let you add bass behind a seat, under the floor or in a thin custom box. The P3SD4-10 is only 3.5 inches deep yet handles 300 watts RMS (600 peak), with an anodized aluminum cone and a vented spider design that helps keep the motor cool.
It is a dual 4-ohm voice coil driver, so you can wire it to suit your amp, and Rockford recommends a 0.5 cubic foot sealed or 1.0 cubic foot vented box. Pair it with the Rockford R2-500X1.
- Only 3.5 inches deep
- 300 W RMS handling
- Dual voice coils for flexible wiring
- Needs a box and an amp
Affordable shallow bass
Pioneer’s TS-A2500LS4 is a lower-cost shallow 10-inch sub rated at 300 watts nominal and 1,200 watts max. Its cone is reinforced with glass fiber and mica for stiffness, and it is designed to match Pioneer’s A-Series speakers.
It is a single 4-ohm voice coil driver, so wiring is simple. Like the Rockford, it needs an enclosure and an external amplifier.
- Low price for a shallow sub
- Stiff reinforced cone
- Simple single-voice-coil wiring
- Needs a box and an amp
- Less refined than the Rockford
How to choose car amplifiers and subwoofers
Door speakers need a 2- or 4-channel amp. Subwoofers need a mono amp. A 5-channel amp can do both.
Amplifier output changes with impedance. Match the amp’s RMS output at your sub’s final impedance to the sub’s RMS rating.
Big boxes take trunk space. Powered and shallow subs fit behind seats and under floors.
Large systems draw a lot of current. Class D amps are efficient and easier on the alternator.
How to match an amplifier to a subwoofer
Start with the subwoofer’s RMS rating and its final impedance (how you wire its voice coils). Then pick a mono amp that produces close to that RMS power at that impedance. For example, a sub rated at 300 watts RMS wired to 2 ohms pairs well with an amp that makes 300 to 500 watts at 2 ohms, set with care. An oversized amp is fine if you set the gain properly; an undersized amp pushed into clipping is what damages subwoofers.
For door speakers, choose a 4-channel amp whose RMS per channel is a little below or equal to the speakers’ RMS rating. Set the amp’s high-pass filter around 80 Hz so the subwoofer handles everything below. Our best car speakers guide lists RMS ratings for each pick, and our sound-quality guide shows a complete matched system.

How to install a car amplifier
-
Plan the route and parts
Choose the amp location, then buy a wiring kit with the right gauge power cable (4-gauge suits most systems up to about 800 W), an inline fuse, ground cable, RCA cables and remote wire.
-
Disconnect the battery
Disconnect the negative terminal before running any power wire.
-
Run the power cable
Route it from the battery through a firewall grommet, away from moving parts, and fit the fuse within 18 inches of the battery.
-
Ground to bare metal
Keep the ground cable short, sand the paint off a solid chassis point, and bolt it tight. Poor grounds cause most noise problems.
-
Run signal wires separately
Route RCA or speaker-level signal wires down the opposite side of the car from the power cable to avoid noise.
-
Set gains and filters
Set crossovers first, then raise gain only until you hear distortion and back off slightly, or use the amp’s gain-setting indicator.
Always fuse the power cable close to the battery, and never connect the battery until all wiring is finished and checked. If you aren’t comfortable working with car electrics, a professional installer is worth it.
Car amplifier and subwoofer FAQ
Do I need an amp for a subwoofer?
Yes, unless it’s a powered (amplified) subwoofer like the Rockford Punch P300-12T, which has the amp built in. Passive subs need a separate mono amp.
What size amp do I need for my sub?
Choose a mono amp whose RMS output at your sub’s final impedance is close to the sub’s RMS rating. For example, the Kicker CXA800.1 suits the 800 W Kicker dual CompR 10 enclosure.
Is a 4-channel amp worth it for factory speakers?
It helps, but you’ll hear the biggest gain if you upgrade the speakers too. A compact amp like the Alpine KTP-445U is a good match for a factory or aftermarket stereo.
Sealed or vented subwoofer box?
Sealed boxes give tighter, more accurate bass and are smaller. Vented boxes play louder and deeper but take more space.
Will a big amp drain my battery?
Not while the engine is running and the system is sized sensibly. Class D amps are efficient. Very large systems may need a bigger alternator or a second battery.
The bottom line
For most people, the best route is a Rockford Fosgate R2-300X4 for the door speakers and a powered sub like the Rockford Punch P300-12T for bass. If you want more, pair the Kicker dual CompR 10 enclosure with the Kicker CXA800.1, or use a shallow Rockford Punch P3S 10 with the R2-500X1 where space is tight. Match RMS power, wire it safely, and set the gains carefully.



